Bently Nevada 330190-080-01-00 3300 XL ETR Extension Cable

Bently Nevada 330190-080-01-00 3300 XL ETR Extension Cable

BENTLY NEVADA · 3300 XL ETR SIGNAL PATH
330190-080-01-00
8.0 m Armored Extended-Temperature-Range Extension Cable
8.0 m cableArmored ETR3300 XL 8 mm system
AVAILABILITY
In Stock · Original New · 1-Year WarrantyGet a Quote
Send Inquiry
Description
EXTENDED-TEMPERATURE SIGNAL PATH · 8.0 M

330190-080-01-00

Armored ETR Extension Cable for the 3300 XL 8 mm System

This is the high-temperature cable segment between a compatible proximity probe and its Proximitor Sensor. Its ordering code specifies an eight-metre run with protective armor and no agency-approval requirement.

Check System LengthSend Cable Label ↗
ORDER CODE AT A GLANCE
080 · 8.0 m cable length
01 · armored construction
00 · approvals not required

⌁ Why the 330190 Family Exists

A standard extension cable may be exposed to temperatures beyond its intended limit when routed near a hot bearing housing, turbine casing or process line. The 330190 family uses the ETR cable construction intended for the hotter part of a 3300 XL 8 mm proximity-transducer installation.

The cable passes the probe signal to the Proximitor Sensor; it does not generate a measurement by itself. Electrical performance depends on the complete probe–cable–driver combination.

☷ Length Arithmetic Before Ordering

Probe lead + extension cable = Proximitor system length

With an 8.0 m extension cable, the probe lead normally completes a 9.0 m system only when the selected probe supplies the remaining 1.0 m. Always calculate from the actual probe part number instead of assuming the total.

330190-080-01-00 Configuration File

Component
ETR extension cable
System family
3300 XL 8 mm
Nominal length
8.0 m / 26.2 ft
Mechanical protection
Armored
Insulation / jacket class
ETR PFA construction
Signal cable
75 Ω triaxial
Probe-side interface
Miniature female coaxial
Driver-side interface
Miniature male coaxial
Approval code
00 · not required

Two Views That Help Confirm the Cable

Bently Nevada 330190-080-01-00 armored ETR extension cable
Overall armored cable construction
Bently Nevada 330190-080-01-00 label and connector detail
Part-number and connector detail
Identification tip: compare the complete printed code and the armor construction. Cable length alone cannot distinguish a standard 330130 cable from an ETR 330190 cable.

Routing Situations

• Turbine and compressor bearing housings
• Cable paths near hot surfaces
• Machinery skids where impact protection is desirable
• Retrofit runs that need an armored ETR segment
• 9 m systems paired with a compatible 1 m probe lead

Three Checks Before Connection

1. Confirm calculated total system length.
2. Verify both mating components belong to the supported 3300 XL 8 mm chain.
3. Keep bend radius, connector cleanliness and environmental protection within installation requirements.

Review My Combination

FAQ · Specific to the 8 m Armored ETR Cable

Is 330190-080-01-00 a proximity probe?

No. It is the ETR extension cable between the probe lead and the Proximitor Sensor. A complete measuring loop still needs the compatible probe and driver.

What is special about the "080" option?

It specifies an 8.0 m nominal cable. The extension length must be added to the probe lead length and matched to the Proximitor total-length option.

Why choose option 01 rather than 00?

Option 01 adds armor for mechanical protection. Option 00 is the non-armored ETR cable. The correct choice depends on routing exposure and the original installation.

Can it replace a 330130-080 cable?

Do not substitute by length alone. The 330190 is the extended-temperature family, while 330130 is the standard-temperature family; verify the probe, environment and system accuracy requirements.

Does approval code 00 cover hazardous-area certification?

Code 00 means agency approval is not required for this ordering configuration. If CSA, ATEX or IECEx documentation is needed, confirm the applicable approval option before purchase.

What should I send for a compatibility check?

Send the probe number, Proximitor number, old extension-cable label, required quantity and installation temperature. Photos of both connector ends are also useful.

PLC EXPORT · Part-Number Review Before Shipment

PLC EXPORT technical sales team meeting

PLC EXPORT supplies industrial automation and machinery-monitoring parts worldwide. For extension cables, our quotation check focuses on the full ordering string, mating probe, driver length and approval requirement-not just the base family.

Send: label photo + probe number + Proximitor number
Receive: availability, lead time and compatibility notes

CONTACT US · 330190-080-01-00

PLC EXPORT customer support team
COMPATIBILITY ENQUIRY
Bently Nevada 330190-080-01-00

Sales Manager: Cristina
Email: sales3@mooreplc.com
WhatsApp / Mobile: +86 180 2071 4662 ↗

Email Cable DetailsWhatsApp ↗

Hot Tags: bently nevada 330190-080-01-00 3300 xl etr extension cable, China bently nevada 330190-080-01-00 3300 xl etr extension cable manufacturers, suppliers, 330103 06 25 10 02 00 review, 330103-06-25-10-02-00, 330104 00 08 90 02 05 3300 XL 8 mm Proximity Probe, 330903 00 05 10 01 05 manual, Bently Nevada 330103 06 25 10 02 00, Bently Nevada 330104 00 08 90 02 05

Send Inquiry