330171-08-24-10-02-00
This configuration is intended for installations where a conventional 8 mm probe cannot be accommodated comfortably. The 5 mm sensing tip observes the gap to a conductive target without contact. When it is connected to the correct 3300 XL extension cable and Proximitor Sensor, the resulting channel can support relative shaft vibration, position and related displacement measurements.
A compact sensing end for restricted mounting locations and smaller target areas.
Verify tapped-hole condition, case reach and locknut position before installation.
Standard cable with a miniature coaxial ClickLoc connection and no armor.

Where its compact geometry helps
The smaller probe does not simply replace every 8 mm installation. It is selected when physical access, target width or bearing geometry requires a reduced sensing footprint.
Read the complete ordering code, not only "330171"
The family number identifies a 3300 5 mm probe, while the suffix describes the physical version being ordered. For this unit, the currently published configuration includes a 1/4-28 UNF threaded case, a 0.8-inch unthreaded length, a 2.4-inch case length and a 1.0 m integral cable. Connector and approval details should be checked against the official ordering information.
| Part identity | 330171-08-24-10-02-00 - compare every suffix block with the removed probe. |
| Cable and connector | 1.0 m integral lead, miniature coaxial ClickLoc; connector protector is not factory included in this configuration. |
| Material envelope | PPS sensing tip with stainless-steel body for industrial machinery-monitoring service. |
| System dependency | Use only with the compatible extension cable and Proximitor Sensor required for the total system length. |
Installation sequence for a controlled replacement
Measure the thread, reach, target clearance and available route before removing the old probe.
Keep the sensing face clean and avoid contact with tools or the target during positioning.
Respect the minimum bend radius, provide strain relief and avoid pulling on the ClickLoc connector.
Set the initial gap and verify the conditioned signal and monitor response before returning the machine to service.
Published technical reference
| Item | Value for this listing |
|---|---|
| Product family | 3300 5 mm eddy-current proximity probe |
| Thread / case | 1/4-28 UNF; 0.8 in unthreaded length; 2.4 in case length |
| Cable | 1.0 m, 75 Ω triaxial FEP, unarmored |
| Connector | Miniature coaxial ClickLoc |
| Published probe temperature range | −35 °C to +177 °C under specified installation conditions |
| Published minimum bend radius | 25.4 mm |
Use these values for identification only; final selection, torque and approval requirements should be verified against the applicable manufacturer documentation.
Frequently Asked Questions
Why would a 5 mm probe be chosen instead of an 8 mm probe?
Can 330171-08-24-10-02-00 operate as a stand-alone sensor?
What is important about the 1/4-28 UNF thread?
What does the ClickLoc connector contribute?
How should the 1.0 m integral cable be routed?
Which checks are recommended after installation?
Before requesting a quotation
Include the entire 330171 suffix and connector view.
Send extension-cable and Proximitor Sensor numbers.
Share thread, reach and clearance if the application is new.
This helps the team prepare a useful availability response.

Check 330171 compatibility and stock
Send the complete part number and mating-system details to Cristina for a focused quotation review.
Email: sales3@mooreplc.com
WhatsApp: +86 180 2071 4662 ↗
Hot Tags: bently nevada 330171-08-24-10-02-00 3300 5 mm proximity probe, China bently nevada 330171-08-24-10-02-00 3300 5 mm proximity probe manufacturers, suppliers, 330180-51-05, 330903 00 05 10 01 05 manual, bently nevada 3300 series and 3300 xl proximity probe, Bently Nevada 330104 00 08 90 02 05, Bently Nevada 330180 51 05, Bently Nevada 330903 00 05 10 01 05

