Bently Nevada 330103-00-02-05-01-00 3300 XL 8 mm Proximity Probe

Bently Nevada 330103-00-02-05-01-00 3300 XL 8 mm Proximity Probe

BENTLY NEVADA · 3300 XL 8 MM
330103-00-02-05-01-00
Metric-thread standard-mount proximity probe for shaft vibration and position
M10 × 10.5 m cable3300 XL 8 mm
AVAILABILITY
In Stock · Original New · 1-Year Warranty
Get a Quote
Sales Manager: Myrtle
Email: sales5@askplc.com
Call or Whatsapp: +86-18950128464
Send Inquiry
Description
3300 XL 8 MM TRANSDUCER COMPONENT

330103-00-02-05-01-00

A standard probe configuration for close-clearance shaft observation

This part number identifies a Bently Nevada 3300 XL 8 mm proximity probe intended to operate inside a complete probe, extension-cable and Proximitor Sensor channel. Its job is to observe the changing distance between the probe tip and a conductive machine surface without physical contact. In a correctly matched system, that distance signal supports both steady shaft-position checks and dynamic vibration monitoring.

What this ordering code tells the buyer

The base number places the item in the 3300 XL 8 mm probe family. The remaining suffixes distinguish mechanical and connection details for this exact version. Because visually similar probes may not be interchangeable, the full code should be compared character by character with the machine documentation or removed component.

Procurement checkpoint: verify probe geometry, mounting thread, system length, connector and approvals as one set.

Signal-chain role

1 · Probe
Senses target gap
2 · Extension
Completes length
3 · Proximitor
Conditions signal

Treat these three elements as a coordinated measurement chain. Mixing lengths or families can alter the expected electrical response.

Selection and installation review

IdentityMatch 330103-00-02-05-01-00 in full; do not purchase from the family number alone.
Mechanical fitCheck thread, bracket or housing engagement, probe reach and clearance around the cable exit.
Electrical matchConfirm the extension cable and Proximitor Sensor belong to the same 3300 XL 8 mm system length.
CommissioningInspect routing, set the operating gap and verify the monitor reading before machine startup.

Where the measurement is useful

Journal bearings
Observe relative shaft vibration inside fluid-film bearing machines.
Axial position
Track changes in shaft location when the target and mounting arrangement are suitable.
Speed reference
Support phase or speed measurements when used with an appropriate target geometry and monitoring channel.
Maintenance checks
Compare gap and vibration behavior during troubleshooting or planned replacement.
330103-00-02-05-01-00 probe detail
Product detail · verify the complete label before ordering

Handling notes that protect accuracy

  • Keep the probe tip clean and protected from impact.
  • Do not use the cable to rotate or tighten the probe body.
  • Provide strain relief without crushing or sharply bending the lead.
  • Separate signal routing from sources of physical damage and electrical noise.
  • Record the final gap voltage and channel response after installation.

Frequently Asked Questions

What does this probe measure?
When paired with the correct 3300 XL extension cable and Proximitor Sensor, it converts probe-to-target spacing into an electrical signal used for radial vibration, shaft position and related displacement measurements.
Is the probe a complete monitoring channel by itself?
No. The probe is one element of a matched transducer chain. Cable length, extension cable and Proximitor Sensor must be selected as a compatible system.
What should be checked before replacing an installed probe?
Verify the entire part number, mounting thread, usable reach, case length, connector style, cable routing and the system length required by the existing channel.
Can it be used on any shaft material?
The system is intended for conductive metallic targets. Target geometry, material and surface condition can influence scale factor, so the machine or OEM installation requirements should be reviewed.
Why is probe gap important?
The initial gap places the signal inside the usable linear range. Final gap setting should follow the monitoring system documentation and the machine manufacturer's procedure.
How should the probe be handled during installation?
Protect the tip from impact, avoid pulling or sharply bending the lead, keep the connector clean and tighten the probe using the specified mounting hardware rather than twisting the cable.

A practical request for quotation

For a faster compatibility check, send the complete installed part number, extension-cable number, Proximitor Sensor number, required quantity and a clear photo of the existing label. This gives the sales team enough context to distinguish a direct replacement from a merely similar 3300 XL probe.

PLC EXPORT team
PLC EXPORT · PRODUCT SUPPORT

Check stock and system compatibility

Share the exact suffix and the mating system components. Myrtle can help review availability and quotation details.

Email: sales5@askplc.com
WhatsApp: +86-18950128464 ↗

Request a Quote
Sales Manager: Myrtle
Email: sales5@askplc.com
Call or Whatsapp: +86-18950128464

Hot Tags: bently nevada 330103-00-02-05-01-00 3300 xl 8 mm proximity probe, China bently nevada 330103-00-02-05-01-00 3300 xl 8 mm proximity probe manufacturers, suppliers, 330103 06 25 10 02 00 review, 330104 00 08 90 02 05 datasheet, 330180 51 05 Extension Cable, 330180-51-05, 330903 00 05 10 01 05 3300 XL 8 mm Proximity Probes, Bently Nevada 330103 06 25 10 02 00

Send Inquiry