Official 3300 XL standard extension cable with 8.5 m length, standard cable construction, connector protector and no agency approval option.
Order and verify the full 330130-085-02-00 code; each suffix changes length, protection or approval.
Code 085 specifies an 8.5 metre (27.9 foot) extension cable.
Code 02 specifies standard cable supplied with a connector protector.
Probe plus 330130-085-02-00 must equal the matched Proximitor Sensor total length.
330130-085-02-00 is the extension-cable element of a Bently Nevada 3300 XL 8 mm proximity transducer system. It connects the probe to the matched 3300 XL Proximitor Sensor and contributes to the tuned electrical length used for non-contact shaft vibration and position measurement.
Baker Hughes requires the probe length plus extension-cable length to equal the total length selected for the Proximitor Sensor. For 330130-085-02-00, an 8.5 m cable normally pairs with a 0.5 m probe to form a 9.0 m system; verify every component label, connector condition and approval requirement before replacement.
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
3300 XL proximity-transducer family
Retain every suffix during quotation and receiving inspection
Used between the probe and Proximitor Sensor
8.5 m (27.9 ft)
Standard cable with connector protector
Agency approval not required
Also used only where the official system documentation permits
Confirm against the actual 330180 Proximitor Sensor code
All three parts form the measurement chain
Applies to a correctly matched complete 3300 XL 8 mm system
Complete system value under documented reference conditions
Set only with the approved commissioning procedure
Do not accept bent, contaminated or loose connectors
Follow the machine and Baker Hughes installation guidance
Total electrical length and approvals must still match
Confirm all items before ordering
Add the installed probe cable length to 8.5 m and confirm the result matches the Proximitor Sensor total length.
Inspect both coaxial connectors and the connector protector for damage, contamination, moisture or looseness.
Record the original route, supports, bend radius, separation and enclosure entries before removal.
Verify gap voltage, static position and dynamic response with the approved 3300 XL procedure after installation.
Carries the probe signal in a matched 3300 XL 8 mm system monitoring shaft vibration.
Supports thrust-position measurement where the probe, target and monitor channel are correctly configured.
Can be part of a documented speed or Keyphasor measurement loop using compatible system components.
Restores a verified 8.5 m extension-cable path while preserving the tuned 9 m system length.
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Use clear front, side, nameplate, connector and terminal photographs. The complete 330130-085-02-00 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

Bently Nevada 330130-085-02-00 connects a 3300 XL probe to its matched Proximitor Sensor in a tuned proximity-transducer system used for non-contact shaft vibration or position measurement.
Bently Nevada 330130-085-02-00 uses length code 085, which the official Baker Hughes ordering table defines as 8.5 metres (27.9 feet).
On Bently Nevada 330130-085-02-00, code 02 specifies standard extension cable supplied with a connector protector; it is not the armored-cable option.
The final 00 on Bently Nevada 330130-085-02-00 means that an agency approval option is not required according to the official ordering information.
Bently Nevada 330130-085-02-00 is commonly combined with a 0.5 m probe to make a 9.0 m tuned system, but the actual probe and Proximitor Sensor labels must be checked.
No. Bently Nevada 330130-085-02-00 is part of a tuned electrical system and should not be cut, shortened or spliced; select the correct official length instead.
No. Bently Nevada 330130-085-02-00 is standard cable with a connector protector. The official 01 option identifies armored cable.
Bently Nevada 330130-085-02-00 should replace another cable only after total system length, probe family, Proximitor Sensor code, cable construction, connector protection and approvals are matched.
Before installing Bently Nevada 330130-085-02-00, inspect the full label, connector pins and shells, protector, jacket, bend condition and the complete probe-to-Proximitor route.
For Bently Nevada 330130-085-02-00, send clear labels for the cable, probe and Proximitor Sensor, installed lengths, connector photos, approval requirement, quantity, destination and required condition.
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
We compare the complete 330130-085-02-00 identity, revision, connectors and visible condition before quotation.
Our team reviews the 330130-085-02-00 host system, slot, wiring and compatibility requirements.
The supplied 330130-085-02-00 markings, connectors and protective packaging are checked before dispatch.
Myrtle coordinates 330130-085-02-00 availability, documents, order details and worldwide delivery follow-up.
sales5@askplc.comWhatsApp
+86 18950128464
Hot Tags: bently nevada 330130-085-02-00 3300 xl 8.5 m extension cable, China bently nevada 330130-085-02-00 3300 xl 8.5 m extension cable manufacturers, suppliers, 330103 06 25 10 02 00 review, 330104 00 08 90 02 05 datasheet, 330180-51-05, 330903 00 05 10 01 05 3300 XL 8 mm Proximity Probes, 330903-00-05-10-01-05, Bently Nevada 330903 00 05 10 01 05

