3300 XL 8 mm probe with M10 × 1 metric thread, stainless-steel armored cable, 0 mm unthreaded length, 70 mm case length and 0.5 m (1.6 ft) total probe-and-cable length.
Retain the full 330104-00-07-05-02-00 code; every option affects mechanical or electrical compatibility.
M10 × 1 metric thread, stainless-steel armored cable; verify 0 mm unthreaded and 70 mm case lengths.
0.5 m (1.6 ft) total probe-and-cable length; match the extension cable and Proximitor Sensor.
miniature coaxial ClickLoc connector; agency approval not required.
330104-00-07-05-02-00 is a 330104 standard-mount probe for the Bently Nevada 3300 XL 8 mm proximity transducer system. In a correctly matched loop it provides a non-contact signal proportional to the distance between the probe tip and a conductive shaft target.
Confirm the complete 330104-00-07-05-02-00 label and add the probe cable length to the extension-cable length; the result must equal the selected Proximitor Sensor total system length.
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
3300 XL 8 mm system
Retain every suffix
M10 × 1 metric thread; stainless-steel armored cable
Verify insertion and target geometry
Verify bracket and locknut position
Probe plus integral cable
Inspect before installation
Match site documentation
Official dimensional drawing
System component value
When correctly matched and installed
Under documented reference conditions
Verify with approved procedure
Flat target reference
Official system reference
All items must match
Record 330104-00-07-05-02-00, extension cable and Proximitor Sensor codes.
Check 0 mm unthreaded length, 70 mm case length, thread and mounting clearance.
Protect the integral cable and connector from crushing, sharp bends, abrasion, heat and contamination.
Verify gap voltage, static position, alarms and dynamic signal before returning the machine to service.
Measures shaft vibration on fluid-film bearing machinery.
Supports thrust-position measurement with the correct target and monitor configuration.
Supports documented speed and phase-reference measurement duties.
Restores a verified probe while preserving the matched transducer-system length.
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Use clear front, side, nameplate, connector and terminal photographs. The complete 330104-00-07-05-02-00 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

Bently Nevada 330104-00-07-05-02-00 is a 3300 XL 8 mm proximity probe used with the matching extension cable and Proximitor Sensor for non-contact shaft vibration, position, speed or Keyphasor measurement.
Bently Nevada 330104-00-07-05-02-00 uses M10 × 1 metric thread. Confirm the machine mounting thread, locknut and probe clearances before installation.
Bently Nevada 330104-00-07-05-02-00 is supplied as stainless-steel armored cable. Preserve the exact base model because armored and unarmored probes have different routing and mechanical requirements.
The documented total probe-and-cable length for Bently Nevada 330104-00-07-05-02-00 is 0.5 m (1.6 ft). Match it with the extension cable and Proximitor Sensor total electrical length.
Bently Nevada 330104-00-07-05-02-00 uses miniature coaxial ClickLoc connector. Inspect the center contact, shell, protector and cable entry before commissioning.
Bently Nevada 330104-00-07-05-02-00 is specified with agency approval not required. The supplied label and site hazardous-area documentation remain the controlling references.
Bently Nevada 330104-00-07-05-02-00 should only replace another probe after thread, unthreaded and case lengths, total cable length, connector, armor, approvals, target material and Proximitor system length are matched.
After fitting Bently Nevada 330104-00-07-05-02-00, verify mechanical gap, static output, channel polarity, alarm behavior and dynamic response using the approved system procedure.
For Bently Nevada 330104-00-07-05-02-00, provide the full label, tip, threaded body, cable, connector, installed position, extension-cable label and Proximitor Sensor label.
Send the complete Bently Nevada 330104-00-07-05-02-00 code, all matched-loop labels, mounting dimensions, connector photos, approval requirement, condition, quantity and destination.
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
We compare the complete 330104-00-07-05-02-00 identity, revision, connectors and visible condition before quotation.
Our team reviews the 330104-00-07-05-02-00 host system, slot, wiring and compatibility requirements.
The supplied 330104-00-07-05-02-00 markings, connectors and protective packaging are checked before dispatch.
Myrtle coordinates 330104-00-07-05-02-00 availability, documents, order details and worldwide delivery follow-up.
sales5@askplc.comWhatsApp
+86 18950128464
Hot Tags: bently nevada 330104-00-07-05-02-00 3300 xl 8 mm proximity probe, China bently nevada 330104-00-07-05-02-00 3300 xl 8 mm proximity probe manufacturers, suppliers, 330103 06 25 10 02 00 3300 XL 8 mm Proximity Probes, 330103 06 25 10 02 00 review, 330104 00 08 90 02 05 datasheet, 330104-00-08-90-02-05, 330180 51 05 manual, 330903 00 05 10 01 05 manual

