Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm Proximity Probe

Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm Proximity Probe

BENTLY NEVADA · 3300 XL 8 MM PROXIMITY TRANSDUCER SYSTEM
Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm Proximity Probe
Long-reach metric 3300 XL 8 mm probe with M10 × 1 thread, a 50 mm smooth sensing-end section, 120 mm case, 1.0 m integral cable and a protected ClickLoc connector joint.
New & original
One-year warranty
3-5 days
Send Inquiry
Description
BENTLY NEVADA · 3300 XL 8 MM PROXIMITY TRANSDUCER SYSTEM
Bently Nevada 330103-05-12-10-01-00 3300 XL 8 mm proximity probe

Long-reach metric 3300 XL 8 mm probe with M10 × 1 thread, a 50 mm smooth sensing-end section, 120 mm case, 1.0 m integral cable and a protected ClickLoc connector joint.

New & original
One-year warranty
3-5 days
PRODUCT AT A GLANCE
What matters when specifying 330103-05-12-10-01-00
Why a user selects it

The 50 mm smooth section reaches through a known stand-off while the 120 mm case retains adjustment and locknut space.

Dimensional acceptance

Measure the installed smooth reach, bracket thickness, target depth and rear cable clearance against the existing assembly.

Connection protection

Code 01 includes the ClickLoc connector protector; inspect its seating, cleanliness and sealing condition during replacement.

System compatibility

The probe contributes 1.0 m to the tuned 3300 XL circuit and carries suffix 00 without the multiple-approval option.

OFFICIAL-DOCUMENT-BASED SUMMARY
Technical specifications

The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.

Manufacturer
Bently Nevada, a Baker Hughes business

3300 XL 8 mm system

Complete model
330103-05-12-10-01-00

Retain every suffix

Probe base
330103

M10 × 1 metric thread; unarmored standard cable

Unthreaded length
50 mm

Verify insertion and target geometry

Overall case length
120 mm

Verify bracket and locknut position

Total length
1.0 m (3.3 ft)

Probe plus integral cable

Connector / cable option
ClickLoc connector with connector protector, standard cable

Inspect before installation

Agency approval
agency approval not required

Match site documentation

Probe tip diameter
8.0 mm (0.31 in)

Official dimensional drawing

Cable impedance
75 Ω

System component value

Complete-system linear range
2 mm (80 mils)

When correctly matched and installed

Complete-system scale factor
7.87 V/mm (200 mV/mil) ±5%

Under documented reference conditions

Recommended system gap
1.27 mm (50 mils)

Verify with approved procedure

Minimum target diameter
15.2 mm (0.6 in)

Flat target reference

Minimum shaft diameter
50.8 mm (2.0 in)

Official system reference

Buyer selection check
Thread, lengths, connector, armor, approvals and system length

All items must match

INSTALLATION CHECKS
Planning a 330103-05-12-10-01-00 replacement
Reach versus adjustment

Confirm the 50 mm smooth section passes through the stand-off while enough of the 120 mm M10 body remains for precise gap adjustment.

Protector and joint

Open and inspect the code-01 protector; verify the ClickLoc connector is fully engaged, clean and free from oil or damaged contacts.

Cable path

Check that the 1.0 m lead reaches the extension cable without tension, sharp bends, rubbing surfaces or a low point that collects fluid.

Reproduce the baseline

Before removal, record probe depth, locknut position, gap voltage and channel reading; reproduce these values during commissioning.

COMMERCIAL DETAILS
Ordering information
PAYMENT

100% advance before shipping

PORT

Xiamen

DELIVERY TIME

3-5 days

CONDITION

New & original; availability confirmed before order

 
LOGISTICS PARTNERS

Carrier selection is arranged according to destination, shipment size and buyer requirements.

DHL
Express
UPS
Worldwide
FedEx
Priority
TNT
International
ARAMEX
Logistics
SF Express
Asia network
IMAGE AND NAMEPLATE REVIEW
Product image and identification notes
PHOTO VERIFICATION
Confirm the exact 330103-05-12-10-01-00 in the photographs

Use clear front, side, nameplate, connector and terminal photographs. The complete 330103-05-12-10-01-00 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

 
Full nameplate
Front and side view
Connector detail
Installed position
330103-05-12-10-01-002x15x121cm01kg1
BUYER QUESTIONS
FAQ about 330103-05-12-10-01-00
Q1
Can a probe with a different smooth reach replace Bently Nevada 330103-05-12-10-01-00?
 

Only after an engineering check. The 50 mm unthreaded reach on Bently Nevada 330103-05-12-10-01-00 determines where the sensing tip sits relative to the stand-off and shaft target.

Q2
May the connector protector from Bently Nevada 330103-05-12-10-01-00 be reused?
 

Reuse the protector for Bently Nevada 330103-05-12-10-01-00 only if it is clean, undamaged, correctly sized and permitted by the maintenance procedure; it must seat around a fully engaged ClickLoc joint.

Q3
Can the 1.0 m integral cable on Bently Nevada 330103-05-12-10-01-00 be modified?
 

No. Cutting or splicing the integral cable changes the calibrated circuit. Bently Nevada 330103-05-12-10-01-00 must retain its original lead and use the specified extension cable.

Q4
What signs suggest that Bently Nevada 330103-05-12-10-01-00 should not be installed?
 

Do not install Bently Nevada 330103-05-12-10-01-00 if the tip is worn, threads are damaged, the cable is crushed or oil-soaked, contacts are contaminated, the protector is cracked or the label is unreadable.

Q5
What information is needed to quote Bently Nevada 330103-05-12-10-01-00 accurately?
 

For Bently Nevada 330103-05-12-10-01-00, send the full label, stand-off and target measurements, connector/protector photos, extension-cable and Proximitor labels, condition, quantity and destination.

ABOUT PLCEXPORT
About PLCEXPORT

PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.

Model verification
Model verification

We compare the complete 330103-05-12-10-01-00 identity, revision, connectors and visible condition before quotation.

Technical coordination
Technical coordination

Our team reviews the 330103-05-12-10-01-00 host system, slot, wiring and compatibility requirements.

Inspection and packing
Inspection and packing

The supplied 330103-05-12-10-01-00 markings, connectors and protective packaging are checked before dispatch.

Customer support
Customer support

Myrtle coordinates 330103-05-12-10-01-00 availability, documents, order details and worldwide delivery follow-up.

CONFIGURATION SUPPORT
Planning a 330103-05-12-10-01-00 replacement?
Send the complete 330103-05-12-10-01-00 label, installed-system details, connector and terminal photographs, required condition, quantity and destination. Myrtle will compare identity and compatibility points before quotation.
Email Myrtle
sales5@askplc.com
WhatsApp
+86 18950128464

Hot Tags: bently nevada 330103-05-12-10-01-00 3300 xl 8 mm proximity probe, China bently nevada 330103-05-12-10-01-00 3300 xl 8 mm proximity probe manufacturers, suppliers, 330103 06 25 10 02 00 3300 XL 8 mm Proximity Probes, 330103-06-25-10-02-00, bently nevada 3300 series and 3300 xl proximity probe, Bently Nevada 330103 06 25 10 02 00, Bently Nevada 330180 51 05, Bently Nevada 330903 00 05 10 01 05

Send Inquiry