Imperial 3/8-24 UNF unarmored 3300 XL 8 mm probe with 3.0 in unthreaded reach, 6.3 in case, 1.0 m integral lead, standard ClickLoc connector and no added approval option.
Code 30 specifies a 3.0 in unthreaded length for deep mounting geometry.
Code 63 specifies a 6.3 in overall case with 3/8-24 UNF-2A thread.
Code 10 supplies a 1.0 m total probe-and-cable length.
Code 02 is standard cable without protector; code 00 adds no approval option.
Bently Nevada 330101-30-63-10-02-00 is a long-reach imperial probe for installations where the sensing tip must extend 3.0 inches beyond the threaded mounting region. The 6.3-inch case gives the mechanical reach and adjustment required while the 1.0 m electrical length is matched directly to a 1 m Proximitor Sensor or combined according to the documented system design.
The 3.0-inch unthreaded section and 6.3-inch case are critical mechanical dimensions. Before replacing Bently Nevada 330101-30-63-10-02-00, compare the mounting bracket depth, target clearance, side clearance and cable exit; do not substitute a shorter stocked probe merely because the thread and connector look similar.
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
3300 XL 8 mm system
Retain every suffix
3/8-24 UNF-2A thread; unarmored standard cable
Verify insertion and target geometry
Verify bracket and locknut position
Probe plus integral cable
Inspect before installation
Match site documentation
Official dimensional drawing
System component value
When correctly matched and installed
Under documented reference conditions
Verify with approved procedure
Flat target reference
Official system reference
All items must match
Measure the full path from the mounting face to the shaft and confirm the 3.0 in smooth reach does not contact the housing.
Check that the 6.3 in body is adequately supported and will not vibrate or bend in service.
Verify 3/8-24 UNF bracket thread, locknuts, wrench clearance and safety-wire practice.
Confirm the 1.0 m lead is used with the intended 1 m system or approved matched configuration.
Reaches a shaft target through a long bracket or housing stand-off.
Provides non-contact shaft-vibration measurement on fluid-film bearing machinery.
Supports axial-position measurement with verified target and installation geometry.
Maintains a documented 3/8-24 UNF installation and 1 m electrical length.
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Use clear front, side, nameplate, connector and terminal photographs. The complete 330101-30-63-10-02-00 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

Bently Nevada 330101-30-63-10-02-00 has a long 3.0 in unthreaded reach and 6.3 in case for deep imperial mounting arrangements.
The long smooth section on Bently Nevada 330101-30-63-10-02-00 can bottom out or contact internal hardware if the housing depth is not verified.
Bently Nevada 330101-30-63-10-02-00 uses 3/8-24 UNF-2A thread and should not be fitted into an M10 metric bracket.
Code 10 gives Bently Nevada 330101-30-63-10-02-00 a 1.0 m total probe-and-cable length.
No. Code 02 on Bently Nevada 330101-30-63-10-02-00 identifies standard cable and the miniature ClickLoc connector.
The final 00 on Bently Nevada 330101-30-63-10-02-00 means the multiple-approval option is not selected.
A shorter probe cannot replace Bently Nevada 330101-30-63-10-02-00 unless an engineering review confirms target reach, bracket support and adjustment range.
Send the Bently Nevada 330101-30-63-10-02-00 nameplate, mounting sketch, measured reach, target details, loop labels, condition, quantity and destination.
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
We compare the complete 330101-30-63-10-02-00 identity, revision, connectors and visible condition before quotation.
Our team reviews the 330101-30-63-10-02-00 host system, slot, wiring and compatibility requirements.
The supplied 330101-30-63-10-02-00 markings, connectors and protective packaging are checked before dispatch.
Myrtle coordinates 330101-30-63-10-02-00 availability, documents, order details and worldwide delivery follow-up.
sales5@askplc.comWhatsApp
+86 18950128464
Imperial 3/8-24 UNF unarmored 3300 XL 8 mm probe with 3.0 in unthreaded reach, 6.3 in case, 1.0 m integral lead, standard ClickLoc connector and no added approval option.
Code 30 specifies a 3.0 in unthreaded length for deep mounting geometry.
Code 63 specifies a 6.3 in overall case with 3/8-24 UNF-2A thread.
Code 10 supplies a 1.0 m total probe-and-cable length.
Code 02 is standard cable without protector; code 00 adds no approval option.
Bently Nevada 330101-30-63-10-02-00 is a long-reach imperial probe for installations where the sensing tip must extend 3.0 inches beyond the threaded mounting region. The 6.3-inch case gives the mechanical reach and adjustment required while the 1.0 m electrical length is matched directly to a 1 m Proximitor Sensor or combined according to the documented system design.
The 3.0-inch unthreaded section and 6.3-inch case are critical mechanical dimensions. Before replacing Bently Nevada 330101-30-63-10-02-00, compare the mounting bracket depth, target clearance, side clearance and cable exit; do not substitute a shorter stocked probe merely because the thread and connector look similar.
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
3300 XL 8 mm system
Retain every suffix
3/8-24 UNF-2A thread; unarmored standard cable
Verify insertion and target geometry
Verify bracket and locknut position
Probe plus integral cable
Inspect before installation
Match site documentation
Official dimensional drawing
System component value
When correctly matched and installed
Under documented reference conditions
Verify with approved procedure
Flat target reference
Official system reference
All items must match
Record 330101-30-63-10-02-00, extension cable and Proximitor Sensor codes.
Check 3.0 in unthreaded length, 6.3 in case length, thread and mounting clearance.
Protect the integral cable and connector from crushing, sharp bends, abrasion, heat and contamination.
Verify gap voltage, static position, alarms and dynamic signal before returning the machine to service.
Reaches a shaft target through a long bracket or housing stand-off.
Provides non-contact shaft-vibration measurement on fluid-film bearing machinery.
Supports axial-position measurement with verified target and installation geometry.
Maintains a documented 3/8-24 UNF installation and 1 m electrical length.
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Use clear front, side, nameplate, connector and terminal photographs. The complete 330101-30-63-10-02-00 identity, revision, markings and physical condition must remain readable and be compared with the installed project.
Bently Nevada 330101-30-63-10-02-00 is a 3300 XL 8 mm proximity probe used with the matching extension cable and Proximitor Sensor for non-contact shaft vibration, position, speed or Keyphasor measurement.
Bently Nevada 330101-30-63-10-02-00 uses 3/8-24 UNF-2A thread. Confirm the machine mounting thread, locknut and probe clearances before installation.
Bently Nevada 330101-30-63-10-02-00 is supplied as unarmored standard cable. Preserve the exact base model because armored and unarmored probes have different routing and mechanical requirements.
The documented total probe-and-cable length for Bently Nevada 330101-30-63-10-02-00 is 1.0 m (3.3 ft). Match it with the extension cable and Proximitor Sensor total electrical length.
Bently Nevada 330101-30-63-10-02-00 uses miniature coaxial ClickLoc connector, standard cable. Inspect the center contact, shell, protector and cable entry before commissioning.
Bently Nevada 330101-30-63-10-02-00 is specified with agency approval not required. The supplied label and site hazardous-area documentation remain the controlling references.
Bently Nevada 330101-30-63-10-02-00 should only replace another probe after thread, unthreaded and case lengths, total cable length, connector, armor, approvals, target material and Proximitor system length are matched.
After fitting Bently Nevada 330101-30-63-10-02-00, verify mechanical gap, static output, channel polarity, alarm behavior and dynamic response using the approved system procedure.
For Bently Nevada 330101-30-63-10-02-00, provide the full label, tip, threaded body, cable, connector, installed position, extension-cable label and Proximitor Sensor label.
Send the complete Bently Nevada 330101-30-63-10-02-00 code, all matched-loop labels, mounting dimensions, connector photos, approval requirement, condition, quantity and destination.
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
We compare the complete 330101-30-63-10-02-00 identity, revision, connectors and visible condition before quotation.
Our team reviews the 330101-30-63-10-02-00 host system, slot, wiring and compatibility requirements.
The supplied 330101-30-63-10-02-00 markings, connectors and protective packaging are checked before dispatch.
Myrtle coordinates 330101-30-63-10-02-00 availability, documents, order details and worldwide delivery follow-up.
sales5@askplc.comWhatsApp
+86 18950128464
Hot Tags: bently nevada 330101-30-63-10-02-00 3300 xl 8 mm proximity probe, China bently nevada 330101-30-63-10-02-00 3300 xl 8 mm proximity probe manufacturers, suppliers, 330103 06 25 10 02 00 3300 XL 8 mm Proximity Probes, 330104-00-08-90-02-05, 330180 51 05 manual, 330903-00-05-10-01-05, Bently Nevada 330103 06 25 10 02 00, Bently Nevada 330104 00 08 90 02 05

