HIMA HIMatrix F2 DO 16 02 16-channel safety relay output remote I/O
HIMatrix safety remote I/O with 16 relay outputs up to 30 V AC / 60 V DC and an integrated two-port 100BASE-TX safeethernet switch.
What matters when specifying HIMatrix F2 DO 16 02
Complete identity
Match every character in HIMatrix F2 DO 16 02, including suffixes and revision markings.
Installed-system basis
HIMatrix F2 DO 16 02 compatibility depends on the documented host system, slot and wiring.
Customer selection check
Confirm 16 relay outputs, maximum 30 V AC / 60 V DC contact potential, connected loads, safeethernet settings and 24 V DC supply.
Replacement planning
Record labels, connectors, settings and diagnostics before removing HIMatrix F2 DO 16 02.
Description and purpose
Documented purpose
F2 DO 16 02 provides sixteen relay outputs for distributed safety applications. HIMA certification identifies relay contact potentials up to 30 V AC or 60 V DC with safeethernet communication through an integrated two-port switch.
Replacement caution
Do not confuse F2 DO 16 02 with transistor-output F2 DO 16 01. Confirm relay contact load, protective circuitry, contact potential, safeethernet configuration and proof-test requirements.
Technical specifications
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
HIMatrix safety remote I/O
F2 DO 16 02
Relay outputs
Do not confuse with F2 DO 16 01
16
Verify contact and terminal allocation
Up to 30 V AC / 60 V DC
Per HIMA certification
2-port 100BASE-TX switch
safeethernet
SIL 3 / Category 4 / PL e
CENELEC SIL 4 documented for certified application
20.4 to 28.8 V DC
Verify complete execution
0 to 50 °C
IECEx data for F2 DO 16 02
Remote output station
Document addressing and resource
Relay load, contact voltage, network, firmware and proof test
All must match
Planning a HIMatrix F2 DO 16 02 replacement
Nameplate record
Photograph the complete HIMatrix F2 DO 16 02 label and all revision markings.
Connector control
Label every plug, terminal and cable before removal; preserve keying and grounding.
Project verification
Compare the host rack, channel allocation, supply and configuration with approved drawings.
Commissioning
Use the manufacturer procedure to verify diagnostics and every affected signal or safety function.
Applications
Safety relay outputs
Switches low-voltage safety circuits.
Shutdown final elements
Controls documented relay-interfaced loads.
Distributed safety
Places output switching near field equipment.
Maintenance replacement
Restores a verified F2 DO 16 02 station.
Ordering information
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Product image and identification notes
Confirm the exact HIMatrix F2 DO 16 02 in the photographs
Use clear front, side, nameplate, connector and terminal photographs. The complete HIMatrix F2 DO 16 02 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

FAQ about HIMatrix F2 DO 16 02
What is HIMatrix F2 DO 16 02 used for?
HIMatrix F2 DO 16 02 is a HIMA HIMatrix remote I/O device with 16 safety-related relay outputs. Its exact duty must be confirmed against the installed-system documentation.
Which system uses HIMatrix F2 DO 16 02?
HIMatrix F2 DO 16 02 belongs to HIMA HIMATRIX. Confirm the controller, rack or remote-I/O execution before ordering.
What specifications matter when selecting HIMatrix F2 DO 16 02?
For HIMatrix F2 DO 16 02, verify confirm 16 relay outputs, maximum 30 v ac / 60 v dc contact potential, connected loads, safeethernet settings and 24 v dc supply. Do not select a replacement from appearance alone.
Can HIMatrix F2 DO 16 02 replace a similar module directly?
HIMatrix F2 DO 16 02 should only replace another unit after the full model, revision, host-system compatibility, connector arrangement and project approval have been confirmed.
Can HIMatrix F2 DO 16 02 be removed while energized?
HIMatrix F2 DO 16 02 must only be removed under the approved isolation, stored-energy and safety procedure for the installed system.
How should HIMatrix F2 DO 16 02 be commissioned?
After installing HIMatrix F2 DO 16 02, verify seating, supply, configuration and diagnostics, then function-test every affected channel under the approved procedure.
What photographs are required for HIMatrix F2 DO 16 02?
For HIMatrix F2 DO 16 02, provide the complete nameplate, front and side views, connector area, installed slot, adjacent hardware and terminal labels.
What should be sent for a HIMatrix F2 DO 16 02 quotation?
Send the full HIMatrix F2 DO 16 02 identity, revision, host system, slot, connector and wiring photographs, required condition, quantity and destination.
About PLCEXPORT
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
Model verification
We compare the complete HIMatrix F2 DO 16 02 identity, revision, connectors and visible condition before quotation.
Technical coordination
Our team reviews the HIMatrix F2 DO 16 02 host system, slot, wiring and compatibility requirements.
Inspection and packing
The supplied HIMatrix F2 DO 16 02 markings, connectors and protective packaging are checked before dispatch.
Customer support
Myrtle coordinates HIMatrix F2 DO 16 02 availability, documents, order details and worldwide delivery follow-up.
Planning a HIMatrix F2 DO 16 02 replacement?
sales5@askplc.comWhatsApp
+86 18950128464
Recommended models
Bently Nevada
HIMA
Hot Tags: hima himatrix f2 do 16 02 safety relay output remote i/o, China hima himatrix f2 do 16 02 safety relay output remote i/o manufacturers, suppliers, HIMA F35 011 Controller, HIMA HIMatrix F35 011, HIMA HIMatrix F35 011 Safety Related, HIMA HIMatrix F60 MI, HIMatrix F35 011, HIMatrix F60 MI 24 01

