GE IC693PBM200 Series 90-30 PROFIBUS Master Module
PROFIBUS-DP master module that lets a Series 90-30 CPU exchange cyclic I/O data and diagnostics with distributed DP slave devices.
Description and purpose
IC693PBM200 is the Series 90-30 rack module used when the PLC must act as a PROFIBUS-DP master. It transfers configured input and output data between CPU memory and compatible DP slaves while also returning slave and network status for diagnostics.
For replacement work, the catalog number alone is not enough. Check CPU firmware, slot assignment, slave addresses, data lengths, termination and the Machine Edition hardware configuration before installation.
Send the module nameplate, CPU model and firmware, rack/slot, PROFIBUS topology and current project file. We will review compatibility before quotation.
Technical specifications
Values summarized from GE Fanuc Series 90-30 PROFIBUS Modules documentation GFK-2121 and Important Product Information GFK-2119A.
Need to verify an installed IC693PBM200 network?
Send Myrtle the full suffix, CPU firmware, rack position, slave count, baud rate, connector details, fault symptoms, quantity and destination. This information helps us identify configuration or termination issues before a replacement is quoted.
Applications
Replace or maintain an installed DP master after firmware and project checks.
Exchange cyclic process data with configured PROFIBUS-DP remote I/O stations.
Connect compatible drives and field devices under a Series 90-30 controller.
Restore legacy PROFIBUS communication while retaining the existing control architecture.
Ordering information
Product image and identification notes
Front-panel details to photograph
Capture the IC693PBM200 catalog number, SYS and COM LEDs, the female PROFIBUS DB9 connector and the male RS-232 service connector. A clear front view helps distinguish the network port from the firmware service port.
Nameplate and installed-system checks
Photograph the full side label and installed rack position. Compare CPU firmware, module revision, bus connector, termination position and project configuration before removing the existing unit.
FAQ about GE IC693PBM200
How do I confirm that IC693PBM200 is the right replacement for my installed PROFIBUS master?
Match the complete IC693PBM200 nameplate, the Series 90-30 CPU model and firmware, the rack slot, the PROFIBUS connector and the existing network configuration. The module requires CPU firmware 8.00 or later, and large networks may require CPU release 10.60 or later.
Can IC693PBM200 replace an older HE693PBM101 without project changes?
Do not treat it as a drop-in swap. GE documents differences in the default status-array size, Clear Mode behavior and the ordering of status bits. Review the project mapping and startup behavior before the replacement is placed in service.
Will IC693PBM200 support the number of slaves and I/O data in my current network?
The module supports as many as 125 DP slaves and up to 244 input bytes plus 244 output bytes for each slave. Actual project capacity still depends on the CPU, scan requirements, configured modules and total network design, so the existing hardware configuration should be checked.
Does IC693PBM200 include PROFIBUS termination inside the module?
No. GE specifies no built-in termination. Use a PROFIBUS bus connector with selectable termination and make sure termination is enabled only at the physical ends of the segment.
Can the RS-232 connector be used as the normal PROFIBUS network port?
No. The female DB9 connector is the PROFIBUS-DP port. The male DB9 RS-232 connector is a service port used for module firmware upgrades; it is not the fieldbus connection.
Which engineering software should I use to configure IC693PBM200?
Configure it with CIMPLICITY or Proficy Machine Edition Logic Developer PLC. GE states that older Logicmaster 90 and VersaPro tools do not support configuration of this module, so confirm the project software before ordering or commissioning.
About PLCEXPORT
PLCEXPORT supports automation maintenance and project teams with model identification, practical compatibility checks and international supply coordination. Our China team reviews labels and order details before dispatch preparation.
Recommended models
Published product references are grouped by brand; each card shows the model only.
GE - published product references
HONEYWELL - published product references
Others - other recommended brands
Need help sourcing a difficult Series 90-30 fieldbus module?
Share the complete model, suffix, quantity and destination with Myrtle for a configuration-aware supply check.
Email MyrtleOpen WhatsAppHot Tags: ge ic693pbm200 series 90-30 profibus master module, China ge ic693pbm200 series 90-30 profibus master module manufacturers, suppliers, ge 90 30 series plc, GE FANUC IC693CPU331, GE FANUC IC693CPU350, GE IC693CPU350, IC693CPU331, IC693CPU350 CPU module


