ABB DSQC256A 3HAB2211-1 robot controller system and safety-status board
Legacy ABB Robotics DSQC 256A system board, product ID 3HAB2211-1, used for controller status, sensor indication and run-chain supervision in documented robot installations.
What matters when specifying DSQC256A 3HAB2211-1
Complete ABB identity
Match both DSQC256A and product ID 3HAB2211-1, including every suffix and revision marking.
Documented function
ABB catalogues the unit as a System Board DSQC 256A for legacy robot-controller service.
Run-chain visibility
Front indications cover AS, MS, GS, ES, LIM and ERR conditions used during controller troubleshooting.
Replacement control
Confirm the controller, rear plane, connectors, wiring and ABB electrical drawings before installation.
Description and purpose
Documented purpose
ABB identifies 3HAB2211-1 as the System Board DSQC 256A. ABB IRB 6400 M94A electrical documentation lists the DSQC 256A in the computer system and documents front-panel indications for three sensor inputs, board initialization and controller operation, together with automatic, manual, general, emergency-stop, limit and relay-mismatch run-chain status.
Replacement caution
DSQC256A is legacy, controller-specific hardware. Do not select it only by the DSQC family name. Match the complete 3HAB2211-1 label, suffix, controller generation, backplane position, connector arrangement, run-chain wiring and project electrical drawings. ABB lists 3HAA3563-ASA as the replaced older product ID, but interchangeability still requires installed-system verification.
Technical specifications
The fields below prioritize the values buyers use for selection. Ratings not traceable to the exact model are intentionally marked for nameplate or project-document verification.
ABB Robotics
Use the complete ABB nameplate for traceability
3HAB2211-1
Primary ordering and identification number
System Board DSQC 256A
Also written DSQC256A
S3
ABB product record; verify the actual installed controller generation
IRB 6400 M94A computer system
ABB troubleshooting documentation identifies AP41 as DSQC 256A
SENSOR 1, 2 and 3; yellow
Brightness follows the received sensor signal level
F red; EN green
F turns off after approved initialization; EN indicates computer operation
AS, MS, GS, ES and LIM; yellow
Used to observe documented safety/run-chain circuit status
ERR; red
Indicates unequal KM1/KM2 relay energization in the documented circuit
3HAA3563-ASA
Confirm compatibility against the controller documentation
Sweden
Official ABB product record
0.3 kg
Official ABB product record
1 piece
Selling unit and order multiple: 1 piece
85389091
Official ABB product classification
Full label, revision, controller model, slot, connectors and wiring
All identity and installation details must be verified before quotation
Planning a DSQC256A 3HAB2211-1 replacement
Controller and slot record
Photograph the robot-controller nameplate, DSQC256A slot, backplane and adjacent boards before removal.
Run-chain evidence
Record AS, MS, GS, ES, LIM and ERR indication states and the relevant electrical drawing references.
Connector and wiring control
Label every connector and cable, photograph orientation and preserve grounding and keying details.
Controlled recommissioning
After installation, verify initialization, EN status, sensor inputs and all affected stop/run-chain functions under the approved ABB procedure.
Applications
Legacy robot maintenance
Restores the documented DSQC256A system-board function in a compatible ABB robot controller.
Safety-status troubleshooting
Provides visible run-chain and relay-mismatch indications for controlled diagnostics.
Planned outage replacement
Supports like-for-like maintenance after full identity, wiring and controller compatibility review.
Critical spare qualification
Creates a traceable spare record using the complete 3HAB2211-1 label, revision and installed-system evidence.
Ordering information
100% advance before shipping
Xiamen
3-5 days
New & original; availability confirmed before order
Carrier selection is arranged according to destination, shipment size and buyer requirements.
Product image and identification notes
Confirm the exact DSQC256A 3HAB2211-1 in the photographs
Use clear front, side, nameplate, connector and terminal photographs. The complete DSQC256A 3HAB2211-1 identity, revision, markings and physical condition must remain readable and be compared with the installed project.

FAQ about DSQC256A 3HAB2211-1
What is ABB DSQC256A 3HAB2211-1 used for?
ABB DSQC256A 3HAB2211-1 is a legacy robot-controller system board. ABB documentation associates it with controller operation, sensor indication and run-chain status monitoring. Confirm the exact controller and electrical drawings before replacement.
Is DSQC256A 3HAB2211-1 a standard PLC I/O module?
No. DSQC256A 3HAB2211-1 is ABB Robotics controller hardware, not a general-purpose PLC I/O module. Its backplane, connectors and safety/run-chain functions depend on the documented robot control system.
Which LEDs are provided on DSQC256A 3HAB2211-1?
DSQC256A 3HAB2211-1 documentation shows SENSOR 1-3, F, EN, AS, MS, GS, ES, LIM and ERR indications. Their states should be interpreted together with the controller troubleshooting and electrical documentation.
What do F and EN mean on DSQC256A 3HAB2211-1?
On DSQC256A 3HAB2211-1, the red F indication turns off when board initialization is approved, while the green EN indication turns on when the computer system is operating. Diagnose unexpected states using the complete controller procedure.
What do AS, MS, GS and ES show on DSQC256A 3HAB2211-1?
DSQC256A 3HAB2211-1 uses AS, MS, GS and ES to show the documented automatic-mode safeguard, manual-mode safeguard, general safeguard and emergency-stop run-chain conditions. Never bypass these circuits during testing.
Can DSQC256A 3HAB2211-1 replace 3HAA3563-ASA directly?
ABB lists 3HAA3563-ASA as the replaced older product ID for 3HAB2211-1, but a direct replacement still requires confirmation of controller generation, suffix, revision, backplane, connectors, wiring and approved ABB documentation.
What should be checked before removing DSQC256A 3HAB2211-1?
Before removing DSQC256A 3HAB2211-1, record the full label, controller model, slot, rear plane, adjacent cards, every connector and wire, grounding, LED states and relevant electrical drawing numbers.
How should DSQC256A 3HAB2211-1 be commissioned after replacement?
After fitting DSQC256A 3HAB2211-1, use the approved ABB service procedure to verify initialization, EN status, sensor indications, automatic/manual/general safeguards, emergency stop, limit circuits and KM1/KM2 supervision.
What photographs are needed for a DSQC256A 3HAB2211-1 quotation?
For DSQC256A 3HAB2211-1, provide clear photos of the full front label, PCB revision, connector side, installed slot, backplane, adjacent modules, controller nameplate and all cable labels.
What information should be sent when ordering DSQC256A 3HAB2211-1?
For a DSQC256A 3HAB2211-1 quotation, send the complete product ID and suffix, controller and robot model, revision, slot, connector and wiring photos, required condition, quantity, destination and any fault or LED symptoms.
About PLCEXPORT
PLCEXPORT supports maintenance, engineering and procurement teams sourcing industrial automation components for active and legacy control systems.
Model verification
We compare the complete DSQC256A 3HAB2211-1 identity, revision, connectors and visible condition before quotation.
Technical coordination
Our team reviews the DSQC256A 3HAB2211-1 host system, slot, wiring and compatibility requirements.
Inspection and packing
The supplied DSQC256A 3HAB2211-1 markings, connectors and protective packaging are checked before dispatch.
Customer support
Myrtle coordinates DSQC256A 3HAB2211-1 availability, documents, order details and worldwide delivery follow-up.
Planning a DSQC256A 3HAB2211-1 replacement?
sales5@askplc.comWhatsApp
+86 18950128464
Recommended models
Bently Nevada
HIMA
Hot Tags: abb dsqc256a 3hab2211-1 robot controller system board, China abb dsqc256a 3hab2211-1 robot controller system board manufacturers, suppliers, abb, ABB SDCS PIN 205B 3ADT312500R0001 Power Interface Board, SDCS PIN 205B 3ADT312500R0001, SDCS PIN 205B ABB, spare part, YPK113A 3AFE61002774

